Water Blaster HY-5000 Pump

Find Similar Products in: Bubble Blaster Pumps Octopus
Water Blaster HY-5000 Pump

Water Blaster HY-5000 Pump
Code: CV-HY-5000W
Price: $229.99

You have: 0 in your basket.
Quantity:  
-OR-

Reef Octopus Water Blaster Circulation Pump
The Water Blaster pumps are based off the same design as the popular Bubble Blaster skimmer pumps but intended to thrust large amounts of water. These pumps feature a digital control circuit board inside that controls directional start up and RPM speeds. The smart circuit board will shut the pump off if it detects a problem that could otherwise have shortened the life of the pump. The Silicone Nitride shafts and bearings deters calcium buildup on the rotor unlike ceramic. This means less maintenance and cleaning and more time for you to enjoy your aquarium instead of working on it! With the performance of these pumps and backing a 3-year warranty how can you go wrong. We offer several different models for water flow and head pressures.

Note: THIS IS NOT A PRESSURE RATED PUMP. This pump is not ideal for second floor applications or to feed Beckett or downdraft skimmers where consistent pressure is necessary.

Water Blaster 5000 Pump Specifications
Voltage: 120v/60Hz
Wattage: 60w
Max Water Flow: 1300gph
Max Head: 12ft
Dimensions (L x W x H): 9″ x 4½” x 8.3″
Inlet Size: 1¼” inlet
Outlet Size: 1” outlet
Efficiency: 95%
Measurements are approximate and can vary.

FEATURES

Low Wattage
Low Heat
Hard Plumb or Hose Barb Connections
Rotatable Volute
Quiet Running
Submersible or External
Digital Circuit Board
Silicon Nitride Shaft & Bearings
3yr warranty

The Water Blaster HY-5000w pump offers super efficiency and performance.

Energy Efficient - Water Blaster pumps consume less energy with improved efficiency compared to other conventional pumps. Operates at a relatively cool temperature with little to no affects on the water temperature of your tank.

Bubble Blaster ImpellerSilicon Nitride Impeller -The Impellers shaft and bearings are made from Silicon Nitride. Unlike other ceramics, Silicon Nitride deters the build up of calcium and super wear-resistance . Therefore reducing maintenance and ensures a longer operating life.

Digital Circuit Board - Digital Control Circuit Board controls directional start-up, RPM speeds and an auto shut-off function if the Water Blaster detects a problem.

3 Year Warranty - Have peace of mind knowing Water Blaster pumps are warranted against defective materials and manufacturing faults of the pump for 36 months.*

Note: THIS IS NOT A PRESSURE RATED PUMP. This pump is not ideal for second floor applications or to feed Beckett or downdraft skimmers where consistent pressure is necessary.

*Guaranteed against defects in materials or workmanship for a period of THREE (3) years from the date of original purchase, under normal use. This warranty is not transferable and is enforced from the date of purchase at retail. Please retain a copy of your sales receipt for proof of purchase. Bubble Blaster pump will be repaired or replaced at manufacturer’s discretion. This warranty does not apply to any Bubble Blaster pump which has been subject to misuse, negligence, tampering or accidental damage. No liability is assumed with respect to loss or damage to livestock or personal property irrespective to the cause thereof. Failure caused by misuse is not covered by this warranty.

MAINTENANCE
Sand and lime deposits may increase the wear of the shaft & bearings considerably and may lead to the exclusion of warranty. To maintain efficient performance of the pump, periodic cleaning is required. Thoroughly clean the pump, the drive assembly and the cooling duct in regular intervals, at least once every six months. In case of high lime content, a lot of sediment or failures, shorter intervals may be necessary.

WARNING: Always unplug or disconnect the pump from the electrical supply before servicing the pump, while the equipment is being installed or when being handled. When inserting or removing the pump from the water, always disconnect main electrical plug. Never yank the cord to pull the plug from outlet. Grasp the plug and pull to disconnect. Always unplug an appliance from an outlet when not in use. Never lift the pump by the cord.

SERVICING / DISASSEMBLY
Unplug pump from power source and detach pump from skimmer body.
Clean outside of pump motor body to remove any accumulated debris or buildup.
Remove volute by unscrewing the Phillips head screws holding it to the pump body.
Remove and inspect impeller, cooling duct and bearings for noticeable signs or wear, damage, debris or buildup * Be sure to handle the impeller shaft with care.
Soak pump body and parts in a solution of vinegar and water (50%-50% mix) for a duration or several hours or more depending on the buildup. DO NOT USE DETERGENTS OR OTHER CHEMICALS CLEANERS which could damage the pump or pollute the aquarium.
Rinse and reassemble the components with care. (You can apply silicone-based lubricant to extend the life of o-rings or gaskets before re-installing.)
Install pump back into operation and plug into power source.
NOTE: To keep the pump in good working order, always replace any worn parts. The pump motor has no user serviceable parts. If the motor or the electrical cord is damaged, discard the pump. If you have any doubts, contact us or your Water Blaster retailer.

Specs & Performance Charts:
Model Inlet/Outlet Dimensions Watts Efficiency Max Flow Max Head Chart
WB2000 3/4" / 1/2" 7x3.5x7" 22 92% 500gph 5.5ft
WB3000 1" / 3/4" 8x4.24x7" 37 96% 750gph 7.5ft
WB5000 1.25" / 1" 9x4.5x7.75" 60 97% 1300gph 11ft
WB7000 1.25" / 1" 9x4.5x7.75 88 97% 1800gph 12ft
WB10000 1.25" / 1" 9.5x5.25x8.5" 130 97% 2600gph 15.5ft
WB12500 1.25" / 1.25" 9.3x5.1x9.1" 175 95% 3250 18.5ft
WB16000 1.25" / 1.25" 9.3x5.1x9.1" 250 93% 4100 16.4ft

 


 
 
Wishlist/Saved Baskets Help?
 
 
 
 
 
 
 
 
Premium Aquatics, Inc.
6050 E. Hanna, STE 4
Indianapolis, IN 46203
ph. 317-895-9005 fx. 317-895-9395