(Our Local Time: 4:33:55 am )
The Majano Wand (patent pending) does not kill through direct electrocution, instead, this device operates on the principles of electrolysis. Since the physical composition of Majano Anemone are mostly water, it essentially disintegrates them on contact.
Wand = 25.5"
Lead Wire = 60"
Output = 12v/500mA
Input = 110v
6 month manufacturer warranty
You say Mojano,
We say Majano.
You say pest and ugly,
We say seek and destroy.
We all say it works like magic!!!
About the Majano Wand
The purpose of the Majano Wand is to eliminate Majano anemones in hobbyist reef aquariums. These “pest” anemones that are accidentally added to reef tanks can multiply very quickly. They should be eliminated because they sting the rare and expensive animals we are trying to house.
The Majano Wand does not kill by electrocuting the animal. It operates on the principal that when electricity is emitted into salt water it produces two gases. One of these gases is hydrogen and it is what is generated at the stainless steel tip. Hydrogen is the lightest element on earth and when the probe touches the Majano it causes the water in the cells of the animal to turn into hydrogen. These animals are mostly water so the animal just disintegrates.
The device operates on low voltage and will not shock you if your hand is in the water. The entire Wand can be submerged but do not get the push button or power supply wet.
CAUTION Keep the device away from children and be very careful that you don’t stick anyone.
Remember, the rod is acrylic and very fragile, it can break, don’t bend it.
Always keep the push button and power adapter out of water.
The probe is dulled but still sharp, be careful.
Only use according to the directions.
1.Uncoil the wires and plug in the power supply. Carefully, remove the plastic cap on the tip of the Majano Wand.
2.Push the button, as you stick the needle in/out and on/over a Majano. Do Not Hold The Button Down when not touching a Majano.
3.Keep sticking the needle in/out and sliding it across the Majano, as it will only kill the parts of the Majano that touch the needle. After five or six insertions, the anemone should be all white and gooey looking.
4.If you see any tentacles or tissue still alive, just touch them/it with the needle while pushing the button. It is sometimes easier to slide the side of the probe along the Majano rather than stick it.
5.If you do not kill the entire animal it is possible for it to regrow in a short amount of time. White “goo” should float to the top when the Majano is dead, remove this goo. Repeat steps 2 and 3 when needed.
6.Don’t keep the button pushed continuously (we are not talking about a minute or two here, we are talking about a larger scale) as the device does emit some gases into the water. (see chart below) After an hour, you can use it again.
7.When finished, Run/Soak the tip in fresh water for a minute and dry completely.
8.Replace the cap and store in original box for safety.
Usage times: (Do not keep the button pushed continuously)
300 gallons————-60 minutes
200 gallons————-40 minutes
100 gallons————-20 minutes
50 gallons—————10 minutes
25 gallons—————5 minutes
After this amount of time, wait an hour for the gases to disperse and it can be used again
Recent Blog Posts
- Maxspect 43.5" Razor 300w 16K LED Fixture
- AI Directors are HERE - control your AI LEDS from ...
- CPR Nano & Mini Reactor Tumbler
- New JBJ LED Nano Cube Aquariums
- New Omega One Frozen Foods - made in USA
- Cobalt Aquatics Protein Skimmer Pumps
- Cobalt Aquatics Neo-Therm Heater (Plastic LED)
- Blue Life Clear FX PRO All-in-one Filtration Media...
- ReefBrite smaller LEDs, 8" to 24" had a nice ...
- Maggie Muffler - Overflow Standpipe Silencer
6050 E. Hanna, STE 4
Indianapolis, IN 46203
ph. 317-895-9005 fx. 317-895-9395